Welcome to HPA. Please login or sign up.

Members
  • Total Members: 375
  • Latest: Bayeux
Stats
  • Total Posts: 6,846
  • Total Topics: 479
  • Online today: 89
  • Online ever: 484 (Oct 19, 2026, 11:51 AM)
Users Online

Recent topics

My First Peanut Scale Build: BD-4 by Bill Hannan

Started by MockwingF, Sep 13, 2026, 02:20 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Stunthenk

#45
What I do is glue the window plastic (I use Evergreen Clear sheet 0,13 mm, item no 9005 J-1) to the fuselage side using either foam friendly CA applied with a pin or nitrate dope applied with a small brush, depending on the structure. I then cover the fuselage sides with the accurately prepared tissue. Finally I stick down the tissue that is framing the windows with some more dope applied with a small brush. This way the plastic windows from the view of the tissue are only a piece of the fuselage side, and not a different item to be glued seperately.
Of course, this the easy method for flat side windows; those with a curvature, or even a double curvature ae an entirely different kettle of fish!

MockwingF

Hi Henk,
Thank you. I will adjust my building process and test the materials.

Markus

MockwingF

Unfortunately, progress has been rather slow recently. Last week I lost quite a bit of time due to a major repair on my Sainte Formule model. During rubber winding, an inattentive RC flyer walked into the fully stretched motor, and the model suffered two fuselage breaks. The wing also required repairs and complete re-covering.

The good news is that yesterday's trimming session was successful, so I am feeling optimistic again.

As for the BD-4, the propeller has been designed and built. The final fine-tuning will be done once the wheels are installed. The wheels are currently under construction and are being cast from 2K PU foam using moulds made from air-drying modelling clay. The masters for the moulds were resin-printed wheel halves.

The coloured side stripes and the registration markings are also in progress.

Hopefully I'll have more progress to report soon!

Markus

Stunthenk

Wicked looking prop! I know next to nothing about props for peanut or somewhat larger rubber  models. Would like some tips, formula or explanation on prop diameter, blade area and pitch versus rubber length / thickness for different sizes of models. Anything to improve on the standard commercial  plastic props.

Piecost

Good to see progress on this nice model. I look forward to reports of it flying and am sure that it will fly well.

Stunthenk,

It is worth getting hold of a.second hand copy of the out of print book:

Making Scale Model Airplanes Fly
William F. McCombs

It is basically and engineering textbook for scale model aeroplanes. But, it has very small type written text and lots of graphs, so is not for everyone.

SP250

Doug Hunt had the McCombs book reprinted for SAM 35 I think - may have some left in stock.

John M

Jmk89

I have an electronic version of McCombs book which I downloaded from somewhere

I will arrange for it to be uploaded to the HPA Plans Gallery in the next day or so.
All the best
Jeremy

Better drowned than duffers, if not duffers won't drown

MockwingF

For my BD-4 Peanut (330 mm wingspan, approximately max. 9 g flying weight including rubber motor), the propeller design was driven by two major constraints.

First, the desired ground clearance with the model sitting level on its landing gear limits the maximum practical propeller diameter to approximately 114 mm.

Second, the relatively wide nose block required a much slimmer blade root section so that the blades could clear the fuselage during rotation. This resulted in a long, narrow transition toward the hub compared to what would normally be chosen purely for aerodynamic reasons.

The final blade outline is a compromise between a classic Antoinette and a Langley propeller shape, aiming to combine sufficient climb performance with a long motor run.

Key Dimensions
Propeller diameter: 114 mm
Radius: 57 mm
Blade length: 40 mm
Maximum blade width: 20 mm
Root width: 5 mm
Maximum width located at approximately 75% of blade length
Target pitch: approximately 150 mm

The limitation to 20 mm maximum blade width was also a compromise.

The blades were cut from 1.0 mm quarter-grain balsa and sanded down to approximately 0.6–0.7 mm thickness before forming. The low weight and dimensional stability of quarter-grain balsa were considered more important than pursuing a perfectly optimized blade outline.

After the blades had been glued to the propeller shaft assembly, the most vulnerable areas, particularly around the blade roots and blade tips, were reinforced with lightweight Japanese tissue. The tissue was applied using a heavily thinned mixture of UHU Hart and acetone, creating an extremely light reinforcement while significantly improving durability.

The propeller shaft tube was made from rolled covering tissue wrapped around a 2 mm drill shank and bonded with the same UHU Hart/acetone mixture.

Pitch Calculation

Pitch was estimated using the standard propeller equation:

Pitch = 2 × π × Radius × tan(Blade Angle)

where:

Pitch = propeller pitch
Radius = measurement radius
Blade Angle = local blade angle at that radius

Using a 45° pitch gauge:

tan(45°) = 1

the equation simplifies to:

Radius = Pitch / (2 × π)

For a target pitch of 150 mm:

Radius = 150 / (2 × 3.1416) = 23.9 mm

Therefore, a blade angle of 45° measured at approximately 24 mm radius from the propeller center corresponds to a pitch of roughly 150 mm.

Forming Jig

The blades are pre-formed using a cylinder with a diameter of 40 mm.

The forming jig used for the propeller blades was inspired by a sketch by Dr. Heinrich Eder published in Saalflug mit Leichtmodellen. The publication was used as a reference for the blade-forming process and also provides valuable background information on propeller geometry, pitch, efficiency, and practical construction techniques for indoor free-flight models.

The required blade alignment angle on the cylinder was derived geometrically from the target propeller pitch. For this design, the theoretical value is approximately 31° relative to the cylinder axis.

The complete derivation of the formula used for this calculation will be presented separately at a later stage.

For practical workshop use, a 30° reference line can be used on the forming cylinder. The difference between the calculated 31° and the practical 30° setup is negligible when compared with the variations introduced by wood properties, moisture content, sanding, gluing, and final trimming of the propeller.

Forming Process
Cut the blade from quarter-grain balsa.
Sand the blade to approximately 0.6–0.7 mm thickness.
Moisten the blade.
Place the blade on a 40 mm diameter cylinder.
Align the blade axis approximately 30° to the cylinder axis.
Allow the blade to dry completely.
Glue the blades to the shaft assembly.
Reinforce the root and tip areas with Japanese tissue and a thinned UHU Hart/acetone mixture.
Verify the final pitch during assembly using the 45° gauge.
Notes

Many of the design parameters are not the result of pure calculation. The final configuration evolved through a combination of geometric analysis, established propeller theory,  free-flight experience, discussions with other modelers, and informed estimation.
Now I just hope it flies as well as it looks on the building board
Markus

Jmk89

Looking at my copy of McCombs book, I downloaded it from the HPA 2 Plans Gallery.  So I think that it is appropriate for it to be on the HPA 3 Plans Gallery too!

The book has been uploaded and will be available once George has sprinkled magic dust over it!
All the best
Jeremy

Better drowned than duffers, if not duffers won't drown


MockwingF


I still owe you the final photos and a short report.
In the end, I finished last in the Peanut Scale class at IIFI 2026, but I am quite proud of my static score. After all, the BD-4 was my very first Peanut Scale model, and I learned an incredible amount throughout the entire building process. I already have my next project in mind.
With a flight time of 24 seconds plus 10 seconds ROG, I was still well below the potential of the model, according to the experienced flyers. At IIFI, I received a lot of constructive advice, especially regarding my propeller. I plan to rework it and continue trimming and optimizing the model over the coming weekends in our local hall. Let's see how far I can take it.
Considering that the model was only completed on Thursday evening and that I was able to start trimming no earlier than Saturday, it already flies remarkably well. It performs beautiful right-hand circles, takes off cleanly from the floor, and lands just as smoothly.
Now it's time for one thing above all: practice, practice, practice!
Many thanks to everyone who supported me with advice, tips, and encouragement. Without the help of the Peanut Scale community, this first model certainly would not have been as successful as it was
Markus


Piecost